LOT #1 QTY = 1

Bulk Bid of Lot #2 to Lot #85: Frozen Vegetable Processing & Packaging Equipment. The line was purchased in 2017 and used less than 6 months. New cost was approximately $3.6 million dollars. It would do IQF vegetables at maximum throughput of 3200 Lbs. per hour, bulk density 18 Lbs/FT3, travel rate of 30 feet per minute ( Bulk Bid Must Be Higher Than What Individual Lots Bring In Total) (Located in Bolingbrook, IL)

   
   
         

LOT #2 QTY = 1

Stainless Steel Structure with (13) spikes used to break up combos of frozen vegetables, 7' W X 51" L X 113" T (Located in Bolingbrook, IL) (Required Rigging Fee: $300.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #3 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #4 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #5 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

       
         

LOT #6 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, Ser. #3926, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #7 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31534623 Fast Back Vibratory Conveyor, Ser. #7932, 10" W X 79" L X 6" sides (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #8 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31534717 Fast Back Vibratory Conveyor, Ser. #7936, 10" W X 74" L X 6" sides (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

       
         

LOT #9 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535425 Fast Back Vibratory Conveyor, Ser. #7351, 10" W X 271" L X 6" sides (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

   
         

LOT #10 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31536410 Fast Back Vibratory Conveyor, Ser. #7938, 8" W X 16' L X 4" Deep with 3 1/2" flat side (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #11 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31536410 Fast Back Vibratory Conveyor, Ser. #7939, 8" W X 16' L X 4" Deep with 3 1/2" flat side (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

       
         

LOT #12 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #13 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #14 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

LOT #15 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, Ser. #3924, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #16 QTY = 1

Stainless Steel 14 Step Stairs with platform, 5' W X 3' L (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #17 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31534052 Fast Back Vibratory Conveyor, Ser. #7352, 10" W X 125" L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
         

LOT #18 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535746 Fast Back Vibratory Conveyor, 8" W X 150" L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #19 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31535700 Fast Back Vibratory Conveyor, Ser. #7354, 10" W X 21' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #20 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535746 Fast Back Vibratory Conveyor, Ser. #7942, 8" W X 150" L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #21 QTY = 1

Stainless Steel Drop Chute, 21" W X 53" L X 31" D flat to 12" X 12" opening (Located in Bolingbrook, IL) (Required Rigging Fee: $250.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #22 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #23 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #24 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #25 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #27 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31534806 Fast Back Vibratory Conveyor, Ser. #7934, 10" W X 5' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #28 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31534043 Fast Back Vibratory Conveyor, Ser. #7356, 10" W X 150" L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #29 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535726 Fast Back Vibratory Conveyor, Ser. #7946, 8" W X 10' L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #30 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31535811 Fast Back Vibratory Conveyor, Ser. #7357, 10" W X 137" L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 

 

 

 
         

LOT #31 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535028 Fast Back Vibratory Conveyor, Ser. #7947, 8" W X 9' L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #32 QTY = 1

Stainless Steel Chute, 20" W X 20" L X 24" D (Located in Bolingbrook, IL) (Required Rigging Fee: $250.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #33 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #34 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #35 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #36 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #37 QTY = 1

Stainless Steel Stairs and Platform, 13 step, L shape, 14' L X 7' W with hand rails (Located in Bolingbrook, IL) (Required Rigging Fee: $600.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #38 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535155 Fast Back Vibratory Conveyor, Ser. #7935, 10" W X 5' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #39 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31534043 Fast Back Vibratory Conveyor, Ser. #7355, 10" W X 12' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #40 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535155 Fast Back Vibratory Conveyor, Ser. #7935, 10" W X 5' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #41 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31536453 Fast Back Vibratory Conveyor, Ser. #7358, 10" W X 19' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #42 QTY = 1

Heat & Control Mdl. CV-FB-260E Fast Back Vibratory Conveyor, no tag, 8" W X 10' L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #43 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #44 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #45 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #46 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
         

LOT #47 QTY = 1

Stainless Steel Platform with 13 stairs, 3' W X 64" L with hand rails (Located in Bolingbrook, IL) (Required Rigging Fee: $600.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

       
         

LOT #48 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31534052 Fast Back Vibratory Conveyor, Ser. #7353, 10" W X 126" L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #49 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535707 Fast Back Vibratory Conveyor, Ser. #7945, 8" W X 13' L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
         

LOT #50 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31536540 Fast Back Vibratory Conveyor, Ser. #7359, 10" W X 21' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
         

LOT #53 QTY = 1

National Bulk Equipment Stainless Steel Combo Dumper, 50' W X 48" Deep, solid carriage with adjustable hold down bar, single hydraulic lift cylinder, 7' tall dump chute, (2) pivot cylinders, 10' 6" dump height, hydraulic power pack, 5 h.p. motor in stainless steel enclosure, 480 volts, 3 phase, 24 volts controls (Located in Bolingbrook, IL) (Required Rigging Fee: $800.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #54 QTY = 1

National Bulk Equipment Stainless Steel Hopper with bottom chopper shafts, 6' W X 6' L X 6' D, tapers to bottom choppers to 12" W X 36" L, stainless steel grid over top of unit, on stainless steel frame, 6' W X 6' L X 10' 6" T, low level sensor, 10/7.5 h.p., 480 volts on cone drive gear box (Located in Bolingbrook, IL) (Required Rigging Fee: $700.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #55 QTY = 1

Stainless Steel Vibratory Conveyor, 12" W X 9' L dimpled tray, on pedestal, system controls (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #56 QTY = 1

Heat & Control Mdl. CV-BT-URTLA30534768 Stainless Steel "Z" Conveyor, 17" wide, 14" useable flighted belt, 4" high, spaced 10" apart, 5' long to rise 19' tall, stainless steel spray bars top & bottom of bolt, 460 volts, 3 phase (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #58 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31534688 Fast Back Vibratory Conveyor, Ser. #7933, 10" W X 6' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #59 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31534656 Fast Back Vibratory Conveyor, Ser. #7937, 10" W X 40" L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #60 QTY = 1

Heat & Control Mdl. CV-FB-90E-G2-TLA31535801 Fast Back Vibratory Conveyor, Ser. #7940, 8" W X 16' L X 4" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #61 QTY = 1

Heat & Control Mdl. CV-FB-260E-TLA31536640 Fast Back Vibratory Conveyor, Ser. #7360, 10" W X 23' L X 6" Deep (Located in Bolingbrook, IL) (Required Rigging Fee: $500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #63 QTY = 1

Stainless Steel Drop Chute, 22" W X 54" L X 24" D with flat down to 12" W X 12" L (Located in Bolingbrook, IL) (Required Rigging Fee: $250.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #64 QTY = 1

Yamato Mdl. ADW-0-0324M Scale, Ser. #WG160913, weight range 8G-1000G, max speed 300W per minute, 220/240 volts, 50/60 hz (Located in Bolingbrook, IL) (Required Rigging Fee: $2,000.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
         

LOT #65 QTY = 1

Yamato Mdl. ADW-0-0324M Scale, Ser. #WG160914, weight range 8G-1000G, max speed 300W per minute, 220/440 volts, 50/60 hz (Located in Bolingbrook, IL) (Required Rigging Fee: $2,000.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
         
         

LOT #66 QTY = 1

Main Platform, all stainless steel construction, approx. 55' L X 40' W, 2 sets of stairs (Located in Bolingbrook, IL) (Required Rigging Fee: $18,00.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #66A QTY = 1

Stainless Steel 4-Door Heat & Control Main Controller for Entire System all Allen Bradley Controls (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
         
         

LOT #67 QTY = 1

Incline Conveyor S-Shape, 14' L X 10" W belt, with 3" cleats, 16" space approx., 9' discharge height (Located in Bolingbrook, IL) (Required Rigging Fee: $400.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #68 QTY = 1

Mdl. JW-A-14 14-Bucket Scale (Located in Bolingbrook, IL) (Required Rigging Fee: $600.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #69 QTY = 1

Incline Conveyor S-Shape, 10" wide belt, with 3" cleats, 10" between cleats, 20' discharge height X 16' L (Located in Bolingbrook, IL) (Required Rigging Fee: $400.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #70 QTY = 1

Incline Conveyor S-Shape, 10" wide belt, with 3" cleats, 18" between cleats, 10' discharge height X 9' L (Located in Bolingbrook, IL) (Required Rigging Fee: $400.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #71 QTY = 1

Mdl. JW-A-14 14-Bucket Scale (Located in Bolingbrook, IL) (Required Rigging Fee: $600.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
         
         

LOT #72 QTY = 1

Incline Conveyor S-Shape, 10" wide belt, with 3" cleats, 10" between cleats, 20' discharge height X 16' L (Located in Bolingbrook, IL) (Required Rigging Fee: $1,500.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #73 QTY = 1

Vestil Mdl. VHPS-2000-AA Lift Dolly, 200 Lb. capacity, Ser. #171693, stacker (Located in Bolingbrook, IL) (Required Rigging Fee: $50.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #74 QTY = 1

Vestil Mdl. VHPS-2000-AA Lift Dolly, 200 Lb. capacity, Ser. #201805001, stacker (Located in Bolingbrook, IL) (Required Rigging Fee: $50.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #75 QTY = 1

Stainless Steel Belt Conveyor, 18" W X 20' 4" L intralox belt, 3 h.p., 230/460 volts, 30" tall adjustable threaded legs (Located in Bolingbrook, IL) (Required Rigging Fee: $150.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #76 QTY = 1

Vibratory Shaker Conveyor, 3' W X 90" L (Located in Bolingbrook, IL) (Required Rigging Fee: $100.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         
       
         

LOT #77 QTY = 1

Equip 90 Degree Conveyor, 18" W X 8' L (Located in Bolingbrook, IL) (Required Rigging Fee: $100.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #78 QTY = 1

Stainless Steel Top Table, 30" W XZ 6' L X 33" T (Located in Bolingbrook, IL) (Required Rigging Fee: $50.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #79 QTY = 1

Stainless Steel Table, 30" W X 8' L X 33" T (Located in Bolingbrook, IL) (Required Rigging Fee: $50.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
   
         

LOT #81 QTY = 1

Stainless Steel Vat, 42" W X 42" L X 40" D stackable (Located in Bolingbrook, IL) (Required Rigging Fee: $25.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

 
 
         

LOT #82 QTY = 1

Stainless Steel Vat, 42" W X 42" L X 40" D stackable (Located in Bolingbrook, IL) (Required Rigging Fee: $25.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

       

LOT #83 QTY = 1

Stainless Steel Incline Conveyor, 24" W X 9' L infeed, 6' discharge, portable (Located in Bolingbrook, IL) (Required Rigging Fee: $100.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #84 QTY = 1

Grid Path Mdl. RDI-17/09 Rotary Dryer, Ser. #GP-RD-2509.1, 18" Dia. X 7' L drum with Grid Path Load Station, Ser. #GP-LS-17-1140 (Located in Bolingbrook, IL) (Required Rigging Fee: $250.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         
         

LOT #85 QTY = 1

Lot of Pac Mac Forming Tubes for Packager, Parts Cart & Misc. Parts (Located in Bolingbrook, IL) (Required Rigging Fee: $50.00-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #85A QTY = 1

Lot of (6) Pac Mac Forming Tubes for Packager, (5) S/S Funnels, (1) S/S fast back tray, misc. parts (Located in Bolingbrook, IL) (Required Rigging Fee: $-Payment Must Be Received by Thursday, November 18th. Removal Starts Wednesday, November 17th and Must Be Removed by Wednesday, November 24th or It Will Be Considered Abandoned. Rigger: Norm Pavlish, Nebraska Stainless, Phone # (402) 540-8843)

         

LOT #86 QTY = 1

Seydelmann Mdl. K120AC8 Stainless Steel 120 Bowl Cutter, Ser. #S8-00120-0622-17, 2 speed knife & bowl, left side unloaoder, complete with stainless steel electrical panel, Command 1000 touchscreen controls (Located in Sandwich, IL)

         
         

LOT #87 QTY = 1

Certo Masosine Mdl. C300-CFG000139 Portable Sine Pump with 2' W X 4' L stainless steel hopper, 2.2 KW, 208-230/460 volts, 3 phase, Ser. #180116-1236 (Located in Sandwich, IL)

 
 
         
         

LOT #88 QTY = 1

Vemag Mdl. DP3 Rotor & Vane Vacuum Filler, (8) stainless steel vanes, Ser. #1380398, Mfg. 2017, 220/440 volts, 3 phase, touchscreen filler device (Located in Sandwich, IL)

 
 
         
         

LOT #89 QTY = 1

Pillar Mdl. Unifoiler U2P10010000D Capper Induction Sealer, Ser. #63994-1, Mfg. 11/2017, 208/240 volts, 1phase, manual controls, digital readout, plastic caps (Located in Sandwich, IL)

 
 
         
       
         

LOT #90 QTY = 1

Concept Automation Bottle Orientator, lid fastener label applicator, 3" W X 17' L plastic belt conveyor, pressure sensitive label applicator (Located in Sandwich, IL)

 
 
         
         

LOT #91 QTY = 1

Concept Automation Waterfall Cap/Lid Feeder with elevator, 2' W X 2' L X 2' Deep, stainless steel hopper, 6" W X 6' T conveyor (Located in Sandwich, IL)

 
 
         
         

LOT #92 QTY = 1

90º Conveyor 3" W X 4' L plastic belt (Located in Sandwich, IL)

 
 
         
       
         

LOT #93 QTY = 1

Danice Mdl. DNC20ADH Portable Air Cooled Scroll Chiller, Ser. #DNC1712081270, Mfg. 2018, 460 volts, 3 phase, R407C refrigerant, 48.8 KW, cooling 69.72 KW, 65.4 h.p., 93.5 h.p. (Located in Sandwich, IL)

 
 
         
         

LOT #94 QTY = 1

Thermal Care Mdl. CRA404H Portable Water Chiller, Ser. #10133010205, Mfg. 2002, 440/480 volts, 3 phase, max temp 120º C (Located in Sandwich, IL)

 
 
         
       
         

LOT #95 QTY = 1

Murzan Mdl. DUS7IM4X4 Stainless Steel Drum Unloading System, Mdl. PI-50 pneumatic diaphragm pump on stainless steel structure, 2 pneumatic cylinders with approx. 52" stroke, 4" dia. sanitary piping reduced to 3" (Located in Sandwich, IL)

 
 
         

LOT #96 QTY = 1

Delaval Contherm Mdl. 6 X 9 Stainless Steel Dual Tube Heat Exchanger, Ser. #HC4293SPN, -20º F at 100 PSI, 6" dia. X 6' long jacketed tubes, dual 15 h.p., 230/460 volt motors (Located in Sandwich, IL)

 
 
         
         

LOT #97 QTY = 1

Formax Mdl. PowerMax 4000 Stainless Steel High Speed 4-Lane Bulk Product Slicer, (4) 40" long product holders with grippers, 8" H X 18" W product throat capable of slicing, shaving and stacking meat products, 15" color touchscreen controller, independent product holder drives, scales and classifiers, 460 volts, 3 phase, Ser. #F5KK80, complete with Formax Mdl. TS-MAX Discharger Conveyor, approx. 14' long neoprene belts, 460 volts, 3 phase, Ser. #13103 (Located in Sandwich, IL)

 
 
         
         

LOT #98 QTY = 1

Provisur-Cashin Mdl. Cashin Edge Multi Slicer, Multi-Slicer, stainless steel construction, 14 1/2" wide X 5 1/4 high throat, 14 1/2" wide feed conveyor, set-up with 4 up jig, 2 3/4" Dia. additional tooling, 3 up -3 1/4" Dia. jig, 8 up 1" up jig, 10 H.P. stainless steel washdown motor, 12" Allen-Bradley Panelview 1250 touch screen controls, 460 volts, 3 phase (Located in Sandwich, IL)

         
         
         

LOT #100 QTY = 1

Koch Stainless Steel Smokehouse, 50" W X 12' L, inside dimensions 50" W X 87" L floor opening, stainless steel spray bars, Koch controls, (2) Chart Recorders, 80" W X 17' L X 9' T overall dimensions, electric fired, 7 1/2 h.p., 230/460 volt motor, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #101 QTY = 1

DEC smoke Generator, Ser. #5708-036, electric fired, 230 volts, 1 phase, stainless steel construction, manual controls, timer (Located in Sandwich, IL)

   
 
         

LOT #102 QTY = 1

Stainless Steel Single Wall Tank, 5' Dia. X 6' Deep, cone bottom, 2" bottom outlet, 88" tall overall with temp probe (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #103 QTY = 1

Stainless Steel Single Wall Tank, 5' Dia. X 6' Deep, cone bottom, 2" bottom outlet, 88" tall overall with temp probe (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #104 QTY = 1

Stainless Steel Single Wall Tank, 5' Dia. X 6' Deep, cone bottom, 2" bottom outlet, 88" tall overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #105 QTY = 1

Stainless Steel Single Wall Tank, 5' Dia. X 6' Deep, cone bottom, 2" bottom outlet, 7' tall overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #106 QTY = 1

Stein Mdl. ABC-III Stainless Steel Batter Mixing Tank, Ser. #886, with 3/4 h.p. stainless steel motor on mixer, stainless steel centrifugal pump on 3 phase motor, Waukesha positive displacement pump on 3 phase motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #107 QTY = 1

Cryovac Hot Water/Steam Shrink Tunnel/Cabinet, 20" W X 18" T X 6' L tunnel, no belt, pump or motors (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #108 QTY = 1

Safeline Metal Detector Aperture, 19 3/4" W X 10" T aperture (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #109 QTY = 1

Stainless Steel Scissor Lift Table, 44" W X 48" L, hydraulic operation (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #110 QTY = 1

Little David Mdl. LDU/3 Case Sealer, Ser. #20013LDU/3, top and bottom tape heads, 110 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #111 QTY = 1

Little David Mdl. LDU/3 Case Sealer, Ser. #20014LDU/3, top and bottom tape heads, 110 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #112 QTY = 1

3M Mdl. 22A Adjustable Case Sealer, Ser. #7882, top and bottom tape heads (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #113 QTY = 1

Lot of (9) Miscellaneous Case Sealer Tape Heads (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #114 QTY = 1

Lightnin Stainless Steel Mixer, 4' long shaft with (3) propellers on Baldor 1.5, 208/230/460 volt motor, mounting bracket (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #115 QTY = 1

Lightnin Stainless Steel Mixer, 4' long shaft with (3) propellers on Baldor 1.5, 208/230/460 volt stainless steel motor, mounting bracket (Located in Plano) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #116 QTY = 1

Lightnin Stainless Steel Mixer, 40" long shaft with (3) propellers on Baldor 1.5, 208/230/460 volt motor, mounting bracket (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #117 QTY = 1

Busch Mdl. RC-0040-AD05-1001 Vacuum Pump, Ser. #C17498, on 2 h.p. motor, 208/230/460 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #118 QTY = 1

Custom Stainless Equipment Mdl. CSC1414.6 Portable Stainless Steel Screw Conveyor, Ser. #84119, 14" Dia. X 16' L auger, 3' wide hopper with safety covers, back end drain, 3 phase motor on gearbox, 9' discharge, 11' 6" tall X 5' W X 16' long overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #119 QTY = 1

Portable Stainless Steel Screw Conveyor, 6" Dia. X 8' L auger, 2' wide hopper 4' high, stainless steel safety covers, 4' discharge, foot pedal activation, 208/230/460 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #120 QTY = 1

MTC Mdl. MTCS-12-6 Portable Stainless Steel Horizontal Screw Conveyor, Ser. #037495, 10" Dia. X 6' L stainless steel auger, 30" W X 4' L X 30" Dia. hopper, 66" discharge, 7' W X 9' L X 113" Tall overall, 2 h.p., 208/460 volt motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #121 QTY = 1

RMF Mdl. 100 Stainless Steel Combo Dumper, 52" W X 48" Deep solid carriage, dual hydraulic lift cylinders, approx. 67" lift height, stainless steel adjustable hold down bars. Complete with hydraulic power pack, 10" W X 18" L X 20" D, 5 h.p. Baldor, 208-230/460 volt motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #122 QTY = 1

Ruhle Dicer, stainless steel construction, set up with 1/4" two way grid set and adjustable speed knife, 230 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #123 QTY = 1

Allen Stainless Steel Vibratory Conveyor, 16" W X 6' L X 2' T, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #124 QTY = 1

Kamflex Mdl. 901B-SP-827 Stainless Steel Accumulation Table, 5' Dia., 33" Tall, Ser. #20031097, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #125 QTY = 1

Stainless Steel Accumulation Table, 45" Dia. X 32" T, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #126 QTY = 1

Ultrasource Mdl. Rhino 4 Tray Sealer, Ser. #1046, 208/240 volts, 3 phase, 2 up, 6 1/2" X 8 1/2" opening, stainless steel gas tank, touchscreen controls, 13" wide film (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #127 QTY = 1

Enviro-Pak Mdl. EG-VBD-5 Natural Wood Smoke Generator, electric fired, 23" Dia., manual controls, Ser. #040-7234-106, 120/480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #128 QTY = 1

Enviro-Pak Mdl. EG-VBD-5 Natural Wood Smoke Generator, electric fired, 23" Dia., manual controls, Ser. #040-7236-107, 120/480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #129 QTY = 1

Enviro-Pak Mdl. EG-VBD-5 Natural Wood Smoke Generator, electric fired, 23" Dia., manual controls, Ser. #040-7236-105, 120/480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #130 QTY = 1

Stainless Steel Single Wall Brine Tank, 21" Dia. X 3" Deep, 2 h.p. dual voltage motor on pump motor, on portable stainless steel frame, 20" W X 53" L (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #131 QTY = 1

Sterling Mdl. M2B2010-F Temperature Control Unit, 2 h.p., 480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #132 QTY = 2

Single Fan Condensing Units, 24" dia. fan, Copeland Mdl. 9RA1-050A-TFC.800 Compressor, 208/230 volts, 3 phase, Freon R 134-A/R409A (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #133 QTY = 1

Stainless Steel Single Wall Brine Tank with additive hopper, 4' Dia X 5' Deep, cone bottom with 25 KW, 230 volts, 3 phase motor on stainless steel centrifugal pump, (2) piece hinged lid & bridge for mixer, 2" valved bottom outlet (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         
 

LOT #134 QTY = 1

Unitherm Tunnel of Fire, natural gas fired, 11" W X 11" H X 54" L tunnel, Siemens Simatic touch panel controls, 15" Dia. exhaust fan, (6) direct gas lines to tunnel, removable stainless steel drip pan, 4' W X 8' L X 5' T overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #135 QTY = 1

Friesens Stainless Steel Combo Dumper, 57" W X 52" D split carriage, 52" W X 5' T dump chute, dual hydraulic lift cylinders, single pivot cylinder, 6' dump height, complete with hydraulic power pack, 21" W X 29" L X 12" D stainless steel reservoir, 3 phase motor, 7' W X 10' L X 7' T overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #136 QTY = 1

Stainless Steel Combo Dumper, 45" W X 56" D solid carriage with hold down bar, dual lift cylinders, 52" dump height, 52" W X 6' T dump chute, complete with hydraulic power pack, 10" W X 18" L X 21" D, stainless steel reservoir, 5 h.p., 230/460 volts, 3 phase motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #137 QTY = 1

FPEC Mdl. HLD725 Stainless Steel Combo Dumper, Ser. #4785, 4' W X 4' D solid carriage with adjustable hold down bars, dual hydraulic lift cylinders, 50" lift height, 6' dump height (adjustable up to 7'), 8" W X 68" T dump chute, 6' W X 6' L X 8' T overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #138 QTY = 1

Stainless Steel Combo Dumper, 53" W X 48" D solid carriage with hold down bar, dual lift & single pivot hydraulic cylinders (housing cracked & shaft bent on left lift cylinder) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #139 QTY = 1

Weber Mdl. CCS WMS Slicer, Ser. #109, Mfg. 4/2009, 480 volts, 3 phase, Weber touchscreen controls, Weber CCRWMS checkweigher, Ser. #109, Weber Mdl. CCW Checkweigher, Ser. #WMS109, Weber CCE exit conveyor, Ser. #109, 16 1/2" W X 14' L neoprene belt, 11 1/2" W X 6" H throat (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #140 QTY = 1

Hermes Mdl. Titan Slicing Line, Ram Feed Slicer with hold down, Siemens Simatic touchscreen controls, SICK light curtain, 15" W X 7" H feed throat, checkweigher, exit conveyor, 18" W X 13' L neoprene belt (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #141 QTY = 1

Hermes Slicing Line Ram Feed Slicer, Siemens Simatic Panel Touchscreen, 15" W X 5" H feed throat (machine incomplete), checkweigher (missing conveyor), exit conveyor, 18" W X 13' L neoprene belt (missing top belt) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         
 

LOT #142 QTY = 1

Hermes Slicing Line Ram Feed Slicer, missing touchscreen, checkweigher, exit conveyor (missing belts), 15" W X 5" high feed slicer (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #143 QTY = 1

SI Hermes Mdl. Titan USNZ Automatic Ram Feed Slicer System, Siemens Simatic panel touchscreen controls, checkweigher, exit conveyor, 18" W X 12' L, 220 volts, 3 phase, Ser. #1205/99 (Located in Sandwich, IL)

   
 
         

LOT #144 QTY = 1

Multivac Mdl. R-230 Thermoforming Rollstock Packager, 420 mm between chains, 2 up die approx. 7 1/4" W X 11" L pockets, Busch vacuum pump, Multivac touchscreen controls, approx. 300 mm advance, 220 volts, 3 phase, Ser. #1763, 44" W X 16' L overall (Located in Sandwich, IL)

   
 
         

LOT #145 QTY = 1

Multivac Mdl. R-230 Thermoforming Rollstock Packager, 320 mm between chains, 2 up die approx. 5 3/8" W X 8" L pockets, Busch vacuum pump, Koch Matrix Label Applicator, Markem Smartdate 5 Code Dater, Multivac Touchscreen Controls, approx. 300 mm advance, 220 volts, 3 phase, Ser. #2308, 44" W X 19' L overall with angle irons (Located in Sandwich, IL)

   
 
         

LOT #146 QTY = 1

Key Mdl. 432183-1 Portable Iso-Flow Stainless Steel Vibratory Conveyor, 40" W X 5' L vibratory tray, 4' W X 6' L X 58" T overall, 230 volts, 3 phase, Ser. #03-104-507 (Located in Sandwich, IL)

   
 
         

LOT #147 QTY = 1

Wolftec Mdl. NT350 Stainless Steel Conveyorized Needle Tenderizer, (2) tenderizing heads with 280 stainless steel needles per head, 24" W X 96" L plastic belt conveyor, 440 volts, 3 phase, Ser. #270, 4' W X 8' L overall (Located in Sandwich, IL)

   
 
         

LOT #148 QTY = 1

Combi Mdl. 2EZ Case Erector, with side load and bottom case sealing tape head, 6' W X 8' L overall(Located in Sandwich, IL)

   
 
         

LOT #149 QTY = 1

Sioux Corp Mdl. HH3G Hybrid Hot Water Natural Gas Fired Boiler, skid mounted with gas pipes and valves, MAWP water 160 PSI, max water temp. 250º F, heating surface 187 sq. ft., min relief valve cap, 3500 Lbs./Hr. power flame natural gas burner, 3 and 5 h.p., 230/460 volt motors, Honeywell fluid power gas valve, national board number #4030, Serial/1511032, Mfg. Ser. #14-4030, 54" W X 16' L X 6' T overall (Located in Sandwich, IL)

   
 
         

LOT #150 QTY = 1

Portable Stainless Steel Conveyor, 16" wide belt, 15' long, 1 h.p. stainless steel motor, 230/460 volts, on gear box, 4' wide X 15' long overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #151 QTY = 1

Stainless Steel "Y" Conveyor, (2) 10" W X 100" L, 22" W X 64" L belt with diverters, with air system, 3 phase, stainless steel motors (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #152 QTY = 1

Stainless Steel Conveyor, 18" W X 9' L plastic belt, (broken missing legs), 230 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #153 QTY = 1

Fomaco Mdl. FGM44/176 Pickle Injector with brine tank and remote pump, 176 needles, 21 1/2" W X 90" L stainless steel conveyor, WEG CFW88 Vector Inverter, 220/440 volts, Ser. #5447 (Located in Sandwich, IL)

   
 
         
 

LOT #154 QTY = 1

General Mdl. DAP2000 Dry Air Pac Air Compressor, 5 h.p., 208-230/460 volts, 3 phase, 15" Dia. X 32" L storage tank (Located in Plano, IL)

 
 
         
   
         

LOT #155 QTY = 1

Fomaco Mdl. FGM44/88 Pickle Injector with brine tank and remote pump, 88 needles, 21 1/2" W X 90" L stainless steel conveyor, Allen Bradley Power Flex, 220/440 volts, 3 phase, Ser. #3151 (Located in Sandwich, IL)

   
 
         

LOT #156 QTY = 1

Groen Mdl. DHT/60 Stainless Steel Natural Gas Fired 60 Gallon Kettle, tilt out bowl, MAWP50PSI@300º F, Ser. #75697 (Located in Sandwich, IL)

   
 
         

LOT #157 QTY = 1

Rollstock Inc Mdl. RI200 Thermoforming Rollstock Packager, 430 mm between chains, set up with 1 up die, approx. 390 mm wide X 560 mm long, approx. 600 mm advance, Busch Vacuum Pump, RAO255B50611XG, Mfg. 2017, Ser. #11496200, 230 volts, 3 phase (Located in Sandwich, IL)

 
 
         
         
         
       
         

LOT #158 QTY = 1

Kramer Grebe Mdl. 3000 Thermoforming Rollstock Packager, 430 mm between chains, set up with 2 up die, 180 mm wide X 280 mm long pockets, approx. 300 mm advance (Located in Sandwich, IL)

 
 
         
         

LOT #159 QTY = 1

Stainless Steel Incline Conveyor, 34" W X 13' L plastic belt, 3' infeed, 67" discharge (Located in Sandwich, IL)

 
 
         
         

LOT #160 QTY = 1

Stainless Steel Incline Conveyor, 34" W X 10' L plastic belt, 67" infeed, 8' discharge (Located in Sandwich, IL)

 
 
         
       
         

LOT #161 QTY = 1

Equip Mdl. 129 Stainless Steel Sorting Table on load cells, 65" W X 20' L table with 15" W X 18' L neoprene belt conveyor, Emery Winslow load cells with Mettler Toledo Digital Weight Indicator, Allen Bradley Power Flex 70 Conveyor, speed control, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #162 QTY = 1

Key Technology Mdl. S109475 Stainless Steel Vibratory Conveyor, 24" W X 6' L slotted tray, Ser. #472097-101697 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #163 QTY = 1

Mettler Toledo Mdl. WH260707 Workhorse Overwrap Packager, Ser. #B342886513, with 707 Auto Labeler, Ser. #B342892043, Smart touchscreen controls, 180º exit conveyor 16" W X 75" L and 5' long packoff conveyor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #164 QTY = 1

Lock Mdl. CK2500 Weigh Check, weight range 10-2500 grams, Ser. #LISI006-6597, needs replacement belts, 3' W X 5' L overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #165 QTY = 1

Hobart Mdl. L800 Mixer, 80 quart stainless steel bowl, (2) whisks, (1) paddle, (1) transfer dolly (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         
 

LOT #166 QTY = 1

Hobart Mixer, 80 quart stainless steel bowl, (2) whisks, (1) paddle, (1) transfer dolly (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #167 QTY = 1

World Cup Packaging Mdl. 12-32 Rotary Cup Filling Machine, 12 station rotary filler, cup dropper, bottom fill up assembly, heat seal unit, pick-n-place lidder, manual controls, change over parts, Ser. #M1224, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #168 QTY = 1

Stainless Steel Dual Action Blender, 19" W X 26" L X 22" D, tilt out bowl, 1 h.p., 208-230/460 volt dual voltage motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #169 QTY = 1

McClain Ozone Ozo Kleen Portable Ozone Cleaning/Sanitation System (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #170 QTY = 1

Stainless Steel Portable Screw Conveyor, 12" Dia. X 9' L screw, 26" infeed hopper, 6' discharge, stainless steel cover (missing motor) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #171 QTY = 1

Stainless Steel Dual Shaft Paddle Blender, hydraulic tilt out bowl, 34" W X 5' L X 30" D with bucket loader (missing hydraulics) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #172 QTY = 1

Waukesha Mdl. 060 Positive Displacement Pump, 3" outlet, stainless steel rotors, 10 h.p., 3 phase motor with control panel (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #173 QTY = 1

Tri-Clover Mdl. TCIP3NLD-20MFY-415L-AQ-DM3A Positive Displacement Pump, Ser. #541550-01, 5 h.p., 208/230/460 volt, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #174 QTY = 1

Econo Lift Incomplete Combo Dumper, single hydraulic lift cylinder, incomplete (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #175 QTY = 1

Jones/Techno Pack Continuous Band Sealer, 4' long (incomplete) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #176 QTY = 1

Mettler Toledo Manual Hand Wrapping Station, 115 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #177 QTY = 1

Atlas Copco Mdl. SFII FF Oil Free Air Compressor, Ser. #A11692583, motor horsepower 7.5 X 3, 200 volts, 3 phase, control voltage 115/24 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         
         

LOT #178 QTY = 1

Fastenal Double Sided Parts Drawer Cabinet with contents, stainless steel bolts, nuts, screws, lock nuts metric and standard, dowels, etc. (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #179 QTY = 1

Lot (14) Plastic Totes, (2) Plastic Bins (Located in Plano, IL) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #180 QTY =

FPEC Stainless Steel Vacuum Tumbler, 6' Dia. X 10' L stainless steel drum, with FPEC Portable Hydraulic Power Pack, 27" W X 5' L X 22" D, 3 phase motor, Hayden heat exchanger, stainless steel platform 80" W X 9' L, stainless steel stairs, Avery-Weigh Tronix Scale with Luga digital readouts, control panel with push button controls and timer (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         
         

LOT #181 QTY = 1

Stainless Steel Framed Conveyor, 24" W X 24' L (no belt), with 10' high stainless steel sides in (2) pieces, missing motor and conveyor ends (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #182 QTY = 1

Supervac Mdl. GK501B Single Chamber Vacuum Packager, Ser. #208118, 20" W X 9' L neoprene belt, 34" W X 4" L chamber, touchscreen controls, Busch RAO250D5Z1XXZZ vacuum pump, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

         

LOT #183 QTY = 1

Carruthers Mdl. SH2000Z Stainless Steel Auto Shredder, 20" Dia. X 4' L shredding drum, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #184 QTY = 1

Grasselli Mdl. NSA600 Slicer, Ser. #S514R0Z/1046, incomplete, 480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

         

LOT #185 QTY = 1

Grasselli Mdl. NSL400 Slicer, Ser. #TOOR131872, incomplete, 480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         
 

LOT #186 QTY =

Grasselli Mdl. NSL400 Slicer, Ser. #U14R041910N, incomplete, 480 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #187 QTY = 1

Biro Stainless Steel Bandsaw, 220 volts, 3 phase, broken head bracket (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

         

LOT #188 QTY = 1

Biro Stainless Steel Bandsaw, 220 volts, 3 phase, broken top wheel holder (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #189 QTY = 1

AEW Mdl. 400LH Stainless Steel Bandsaw with aluminum head, 220 volts, 3 phase, Ser. #1334748 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         
         

LOT #190 QTY = 1

AEW Mdl. 400M Bandsaw, mixed metal construction, 220 volts, 3 phase, Ser. #LHS340897 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #191 QTY = 1

AEW Mdl. 400LH Bandsaw with aluminum head, missing top wheel, 220 volts, 3 phase, Ser. #1334746 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

         

LOT #192 QTY = 1

Multivac Mdl. ASE500 Portable Vacuum Trim Canister, Ser. #20082239, 230 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #193 QTY = 1

Keymac Mdl. K50 Extended Pitch Auto Sleeving Machine, 9" W X 54" L infeed conveyor, 8 1/2" W X 7 1/2" L magazine, pneumatic feed cylinder with 10" stroke, with spare magazine 10 1/4" W X 9 1/2" L (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #194 QTY = 1

Keymac Mdl. K50 Extended Pitch Auto Sleeving Machine, 9" W X 54" L infeed conveyor, 8" W X 18" L magazine, pneumatic feed cylinder with 10" stroke (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #195 QTY = 1

CVP Mdl. A300 Portable Bag Sealer, 34" seal bar, stainless steel vacuum snorkels, two finger activation, digital controls, adjustable bag tray (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #196 QTY = 1

Motoweigh/Rice Lake Checkweigher, 24" W X 44" L conveyor, Rice Lake digital readout, Rice Lake Mdl. 24 X 44 E, capacity 60 Lb. X .05 Lb., Ser. #150323RL1-6122, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #197 QTY = 1

Mettler Toledo Mdl. CM600XS Checkweigher, Ser. #14022312, 24" W X 16" L Conveyor, Mettler Toledo Hi-Speed 15" Color Touch (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #198 QTY = 1

Loma Mdl. IQ2 Portable Metal Detector, 19 3/4" W X 15 3/4" high aperture, 18" W X 8' L plastic belt conveyor, missing conveyor drive motor, Ser. #KIMH19874A (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
         

LOT #199 QTY = 1

Easty Mdl. EET2010 Electric Shrink Tunnel, Ser. #112E2010TL, Mfg. 8/11, 220 volts, 1 phase, 20" W X 12" H X 3' L tunnel, manual controls with digital readout (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #200 QTY = 1

Busch Mdl. RAO630 Vacuum Pump (Rebuilt by TMS in 2015), on aluminum frame, heat exchanger, 480 volts, 3 phase motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         
       
         

LOT #201 QTY = 1

Busch Mdl. RAO400B0331002 Vacuum Pump, Ser. #U064405826, stainless steel platform, 15 h.p. motor, 460 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #202 QTY = 1

Busch Mdl. WV1000 Vacuum Booster Pump, 5 h.p. motor, 460 volts, Ser. #5592984 (rebuilt by TMS) (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #203 QTY = 1

Busch Mdl. WV500 Vacuum Booster, 3 h.p. motor, 460 volts, Ser. #9915000337 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #204 QTY = 1

Loveshaw Mdl. CF5/E Little David Carton Erector,Ser. #2411799CF5/E with Mdl. LD3SB/3 Case Sealer with top and bottom tapers, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

         

LOT #205 QTY = 1

Loveshaw Mdl. CF5/E Little David Carton Erector, Ser. #4211600CF5/C with Mdl. LD3SB/3 Case Sealer with top and bottom tapers, 120 volts, incomplete (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
   
   
         

LOT #206 QTY = 1

Ishida Mdl. DACS-GN-5060-35/CRI-S Scale, parts machine (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #207 QTY = 1

Ishida Mdl. DACS-GN-5060-35/CRI-S Scale, parts machine (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #208 QTY = 1

Ishida Mdl. DACS-GN-5060-35/CRI-S Scale, parts machine (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #209 QTY = 1

Ishida Mdl. DACS-GN-5060-35/CRI-S Scale, parts machine (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #210 QTY = 1

Motoweigh/Rice Lake Checkweigher, 24" W X 44" L conveyor, Rice Lake digital readout, Rice Lake Mdl. 24 X 44 E, capacity 60 Lb. X .05 Lb., Ser. #150323RL1-6122, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 

 
 
         
       
         

LOT #211 QTY = 1

Stainless Steel Conveyor, 18" W X 80" L plastic belt, 1 h.p. motor, 230 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #212 QTY = 1

Stainless Steel Conveyor, 24" W X 6' L plastic belt with rubber, hydraulic motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #213 QTY = 1

Equip Stainless Steel Conveyor, 16" W X 64" L plastic belt, no motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #214 QTY = 1

Stainless Steel Conveyor, 24" W X 90" L plastic belt with stainless steel weldments, 8' long overall, hydraulic motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

 
 
         

LOT #215 QTY = 1

Stainless Steel Conveyor, 24" W X 56" L plastic belt, indexing panel with controls, stainless steel motor, 230 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #216 QTY = 1

Stainless Steel Conveyor, 12" W X 5' L (no belt), control panel, stainless steel motor, 120 volt plug (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #217 QTY = 1

Stainless Steel Scale Platform, 24" X 24" (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #218 QTY = 1

Stainless Steel Scale Platform, 24" X 24" (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #219 QTY = 1

Thompson Scale Co. Mdl. TSC350 Checkweigher, dual lanes, (2) scales, each side 12" W X 5' L (no belts), Mdl. 5511 digital touchscreen controls (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #220 QTY = 1

Stainless Steel Floor Scale, 4' W X 5' L platform with curbs, stainless steel ramp 4' W X 4' L, Rice Lake 420 digital indicator (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #221 QTY = 1

Loma Mdl. IQ2 Metal Detector, 19 3/4" W X 3" T aperture, 16" W X 5' L plastic belt conveyor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #222 QTY = 1

Lazy Susan Turntables, 5' dia. poly tops, stainless steel frame, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         
 

LOT #223 QTY = 1

Hydraulic Power Pack, 12" W X 36" L X 8" D, stainless steel reservoir (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #224 QTY = 1

Lot Fiberglass Enclosures (2) 24" W X 24" L X 9 1/2" D, (1) 15" W X 15" L X 5" D, with red stack light (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #225 QTY = 1

Temco Mdl. TT1004 Transformer in 3R enclosure, Type: ANN, 3 phase, ISO, 60 hz, primary voltage 208/240/480, delta H1, H2, H3, secondary voltage 380/400/415 Y (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #226 QTY = 1

Ultrasource Mdl. Matrix Label Applicator, crossweb, parts machine (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #227 QTY = 1

Dorner Portable Transfer Conveyor, 6" W X 3' L belt, last used with ink jet printer (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #228 QTY = 1

Ice Tech Mdl. Elite 20 Evolution Line, portable (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #229 QTY = 1

Miller Mdl. Syncrowave 250 CC AC/DC Welding Power Source, 200/230/460 volts, 1 phase, Ser. #LA072891, with foot pedal (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #230 QTY = 1

Miller Mdl. Micromatic 150 CV-DIC Welding Power Source, 200/300/460 volts, 1 phase, Ser. #KF797845 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #231 QTY =

Thermal Dynamics Pakmaster Mdl. 75XL Plasma Cutter with PCH/M-75 Torch (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #232 QTY =

 

   
 
         

LOT #233 QTY = 1

Stainless Steel Metal Detector Conveyor, 18" W X 114" L plastic belt, 44" wide X 114" overall (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #234 QTY = 1

Stainless Steel Conveyor, 24" W X 11' L plastic belt, with weldments, 3 phase motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #235 QTY = 1

Mettler Toledo Safeline Metal Detector, 13 3/4" W X 5 3/4" H aperture, 12" W X 11' L conveyor (no belt), 1/2 h.p., stainless steel dual voltage motor, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #236 QTY = 1

Lot Pallet Racking (12) Uprights 42" W X 12' T, 60 Crossbeams 8' wide (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #237 QTY = 1

CP Packaging Vision Pak 5 Vacuum Packaging Machine, 26" between chains, (2) Ultrasource Matrix Labelers, touchscreen controls, vacuum pump, tooling: 8 up, 5 1/2" wide X 7 1/2" long oval molds with perforated tool (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #238 QTY = 1

Triangle Mdl. 822C Vertical Form, Fill & Seal System Includes: 3 lane vibratory conveyor, (9) bucket 4" X 6" stainless steel scale, vertical form fill & seal with touch screen controls, Ser. #120422, incline conveyor 14" W X 22' L flighted belt, 2" high flights, 12" spacing, stainless steel electrical panel, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #239 QTY = 1

Portable Stainless Steel Incline Conveyor, 18" W X 11' L neoprene belt, 12" infeed, 5' discharge, 230 volt drum roller motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #240 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #241 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #242 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #243 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #244 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #245 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #246 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #247 QTY = 5

Stainless Steel Smoke Trucks, 41 1/2" W X 42 1/2" L X 81" T, 4 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #248 QTY = 6

Stainless Steel Smoke Trucks, 43" W X 44" L X 80" T, 3 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #249 QTY = 6

Stainless Steel Smoke Trucks, 43" W X 44" L X 80" T, 3 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #250 QTY = 5

Stainless Steel Smoke Trucks, 43" W X 44" L X 80" T, 3 spaces for sticks or screens, 17" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #251 QTY = 3

Stainless Steel Smoke Trucks, 41" W X 43" L X 81" T, 3 spaces for sticks spaced 17" bottom, 13" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #252 QTY = 2

Stainless Steel Smoke Trucks, 43 1/2" W X 48" L X 80" T, 7 spaces for screens, spaced 9 1/2" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #253 QTY = 2

Stainless Steel Smoke Trucks, 33" W X 43" L X 69" T, 8 spaces, 5" and 8" apart for sticks (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #254 QTY = 4

Stainless Steel Smoke Trucks, 33" W X 46" L X 69" T, 9 spaces, 5" and 6" apart for sticks (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #255 QTY = 1

Lot of Stainless Steel Smoke Trucks, (1) 31" W X 52" L X 79" T, 9 spaces 7" apart, (1) 31" W X 54" L X 76" T, 8 spaces, 7" apart, (1) 43" W X 47" L X 80" T, 10 spaces, 6" apart, (1) 43" W X 43" L X 80" T, 4 spaces, 16" apart, (1) 42" W X 43" L X 74" T, 4 spaces, 13" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #256 QTY = 8

Stainless Steel Belly Hanging Racks, 30" W X 6' L X 80" T, holds up to (60) bellies (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #257 QTY = 8

Stainless Steel Belly Hanging Racks, 30" W X 6' L X 80" T, holds up to (60) bellies (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #258 QTY = 1

Stainless Steel Belly Hanging Rack, 40" W X 5' L X 80" T, holds up to (64) bellies (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #259 QTY = 1

Pizzamatic Cheese Dropper/Water Fall Topping Applicator, 45" W X 7' L conveyor, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #260 QTY = 1

Quantum Mdl. QTGA2000 Portable Seasoning Applicator, 36" long trough, 1/2 h.p., 230 volts, Ser. #QTGA20510401 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #261 QTY = 1

Graham Tube & Shell Heat Exchanger, approx. 1250 sq. ft., horizontal carbon steel shell rated, 20 psi @ 300º F (321) brass 3/4" dia. X 20' long tubes, rated 75 psi @ 200º F, openings shell (2) 1 1/2" tube, (2) 6", (3) pass design, saddle mounted national board #39567, Ser. #10-77424T (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #262 QTY = 1

Hobart Mdl. 4356 Mixer Grinder, 500 Lb. capacity hopper, 15 h.p. grinder motor, 5 h.p. mixer motor, 220 volts, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #263 QTY = 1

Hobart Mdl. SC90-56 Vertical Screw Conveyor, 220 volts, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #264 QTY = 1

Hobart Mdl. 4356 Mixer Grinder, 500 Lb. capacity hopper, 15 h.p. grinder motor, 5 h.p. mixer motor, 220 volts, 3 phase (missing grinder auger) (Located in Sandwich, IL)

   
 
         

LOT #265 QTY = 1

Hobart Mdl. SC90-56 Vertical Screw Conveyor, Ser. #27-027-148, 220 volts, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #266 QTY = 1

Mid States Tank Co. Stainless Steel 7' Dia. X 11' Deep Single Wall Tank, 9' straight side, 2 1/2" bottom outlet, 16" manhole, 13' tall overall with legs and inlet, Ser. #13905 (Located in Sandwich, IL)

   
 
         

LOT #267 QTY = 1

Snyder Industries Poly Tank, 8' Dia. X 11' Deep Tank, 9' straight side, 16" manhole, 2 1/2" bottom outlet, 13' tall overall tank with 90" Dia. X 41" T frame (Located in Sandwich, IL)

   
 
         

LOT #268 QTY = 1

AND Mdl. FG-30KBM Digital Scale, 12" X 15" stainless steel top, battery operated, 60 Lb. X 0.005 Lb. capacity, Ser. #Q2009078 (Located in Sandwich, IL)

   
 
         

LOT #269 QTY = 1

AND Mdl. FG-30KBM Digital Scale, 12" X 15" stainless steel top, no battery, 60 Lb. X 0.005 Lb. capacity, Ser. #Q2008675 (Located in Sandwich, IL)

   
 
         

LOT #270 QTY = 1

AND Mdl. FG-30KBM Digital Scale, 12" X 15" stainless steel top, no battery, 60 Lb. X 0.005 Lb. capacity (Located in Sandwich, IL)

   
 
         

LOT #271 QTY = 1

AND Mdl. SJ-12KHS Digital Scale, 7 1/2" X 9" stainless steel top, battery operated (Located in Sandwich, IL)

   
 
         

LOT #272 QTY = 1

Turbo Chef Mdl. HC51618 High Heat Ventless Rapid Cook Counter Top Conveyor Pizza Oven, 16" W X 21" L conveyor, Ser. #HHC1618DED00057 (Located in Sandwich, IL)

   
 
         

LOT #273 QTY = 1

Turbo Chef Mdl. HC51618 High Heat Ventless Rapid Cook Counter Top Conveyor Pizza Oven, 16" W X 21" L conveyor, Ser. #HHC1618DED00078 (Located in Sandwich, IL)

   
 
         

LOT #274 QTY = 1

Cook Tek Mdl. MC1800 Induction Magna Wave Oven, Ser. #6006-17199-C7815, 14" X 14" top, lit up, 110 volts (Located in Sandwich, IL)

   
 
         

LOT #275 QTY = 1

Cook Tek Mdl. MC1800 Induction Magna Wave Oven, Ser. #6006-16064-C7055 14" X 14" top, lit up, 110 volts (Located in Sandwich, IL)

   
 
         

LOT #276 QTY = 1

Cook Tek Mdl. MC1800 Induction Magna Wave Oven, Ser. #6006-16228-C7286, 14" X 14" top, lit up, 110 volts (Located in Sandwich, IL)

   
 
         

LOT #277 QTY = 1

Cook Tek Mdl. MC3500G Induction Magna Wave Oven, Ser. #6204-13259-C0654, 200/240 volts (Located in Sandwich, IL)

   
 
         

LOT #278 QTY = 1

Cook Tek Mdl. MCD2502F Induction Magna Wave Oven, Ser. #6019-15279-C5692, 200/240 volts, 14" W X 27 1/2" L, front and back burners, no controls (Located in Sandwich, IL)

   
 
         

LOT #279 QTY = 1

Cook Tek Mdl. MC3502G Induction Magna Wave Oven, Ser. #6207-13018-C0094, 200/240 volts, 14" W X 27 1/2" L, front and back burners (Located in Sandwich, IL)

   
 
         

LOT #280 QTY = 1

Equipex Mdl. Panini VC Flat Panini Grill, Ser. #VB509055, tested heated up (Located in Sandwich, IL)

   
 
         

LOT #281 QTY = 1

Star Mfg. Mdl. PST14 Panini Grill, Ser. #PST140617A0073, lit up heated up (Located in Sandwich, IL)

   
 
         

LOT #282 QTY = 1

Star Mfg. Mdl. PST14 Panini Grill, Ser. #PST140417A0064, lit up heated up (Located in Sandwich, IL)

   
 
         

LOT #283 QTY = 1

Star Mfg. Mdl. PST14 Panini Grill, Ser. #PST140917A0026, lit up heated up (Located in Sandwich, IL)

   
 
         

LOT #284 QTY = 1

Star Mfg. 10" Panini Grill (Located in Sandwich, IL)

   
 
         

LOT #285 QTY = 1

Nemco Manual Vegetable Chopper with 1" X 1" square knife (Located in Sandwich, IL)

   
 
         

LOT #286 QTY = 1

Robot Coupe Mdl. CL50 Vegetable Processor, (7) chopping tools, (2) ES 2 5/64", (2) 10 3/8", (1) 6 1/4", (1) 1 3/64", (1) Grater, (1) 1/4" Dice, tested works (Located in Sandwich, IL)

   
 
         

LOT #287 QTY = 1

Lot of (3) Crathco Mdl. CS-4E/2d/3d-16 Beverage Dispensers, plugged in, all (3) lit up (Located in Sandwich, IL)

   
 
         

LOT #288 QTY = 1

Vollrath Mdl. 747 Mirage Induction Rethermalizer, Ser. #G051-00300751-071 (new in box) (Located in Sandwich, IL)

   
 
         

LOT #289 QTY = 1

Vollrath Mdl. 747 Mirage Induction Rethermalizer, Ser. #H023-00337702-012 (Located in Sandwich, IL)

   
 
         

LOT #290 QTY = 1

Carter Hoffman Crisp & Hold Food Warmer (Located in Sandwich, IL)

   
 
         

LOT #291 QTY = 1

Merco Mdl. FFHS-10 Food Warmer (Located in Sandwich, IL)

   
 
         

LOT #292 QTY = 1

Delfield Mdl. 407CA Shallow Depth Under Counter Freezer, 4.7 Cu. Ft., single rack (Located in Sandwich, IL)

   
 
         

LOT #293 QTY = 1

Vulcan Hart Grill, missing 2 top pieces (Located in Sandwich, IL)

   
 
         

LOT #294 QTY = 1

Continental Refrigeration Mdl. MDIVACB36-101 Griddle Stand Refrigeraror, Ser. #650129514, 2-drawers, 36" wide on wheels (Located in Sandwich, IL)

   
 
         

LOT #295 QTY = 1

Piper Mdl. TFC-CW 2-Fan Evaporator, 27" W X 7' L, with compressor (Located in Sandwich, IL)

   
 
         

LOT #296 QTY = 1

Pro Seal Mdl. GT5e Automatic High Speed Dual Lane Inline Tray Sealing System, Ser. #3551, incudes (4) portable tool carts, (2) 8 up tool sets approx: 6" W X 8" L Ser. #0-04192, Ser. #T26587-200-1, (1) 4 up tool set approx. 6" W X 15 1/2" L Ser. #T2663-PT-HR, (1) 4 up tool set approx. 6" W X 15" L, Ser. #T251500-200-1, dual lane outfeed conveyor, 24' long, skid of parts (Located in Sandwich & Plano, IL)

   
 
         

LOT #297 QTY = 1

Lazy Susan, 4' dia. poly top, 6" tall stainless steel sides, Penta Drive speed controls, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #298 QTY = 1

Lazy Susan, 4' dia. poly top, 3" tall poly sides, Penta Drive speed controls, 120 volts (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #299 QTY = 1

Stainless Steel Sink, 18" W X 54" L, (3) faucets, knee activation (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #300 QTY = 1

Kamflex Mdl. 327LF Volumetric Piston Filler, Ser. #18007, 55" X 37" hopper, 3" L X 2.5" Dia. piston, 1/2" inlet & outlet with sanitary pipe and clamps, air operated with foot pedal (Located in Skokie, IL)

   
 
         

LOT #301 QTY = 1

MTC High Lift Vat Dumper, designed for high lift discharge, forklift loading, mounted on MTC LEC Sub-Base for a 106" discharge height, 10 h.p. hydraulic power pack, 440 volts, 3 phase, 60 hertz (Located in Skokie, IL)

   
 
         

LOT #302 QTY = 1

Ultrasource Mdl. PL52 Matrix Top & Bottom Crossweb Automatic Film Labeler (Located in Skokie, IL)

   
 
         

LOT #303 QTY = 1

Handtmann Mdl. 217-21 Length Linking Unit, spare parts & Handtmann 412 Holding Device (Located in Skokie, IL)

   
 
         

LOT #304 QTY = 1

Loma Mdl. IQ2 Metal Detector, dual head design, 13 3/4" X 2 7/8" aperture, 6" wide plastic conveyor belt, Baldor 1/2 h.p. motor, 220 volts, 3 phase, 60 hz, mounted on stainless steel frame, pneumatic reject (Located in Skokie, IL)

   
 
         

LOT #305 QTY = 1

Transfer Conveyor, 39" wide conveyor belt X 66" long, 1/3 h.p. direct drive motor, 230 volts (Located in Skokie, IL)

   
 
         

LOT #306 QTY = 1

Incline Frozen Block Conveyor, stainless steel frame, 24" wide cleated belt X 96" long, 22" between cleats, 230/460 volts, 3 phase, 60 hz, 25" infeed and 70" discharge height on 4" casters, 3/4 h.p. drive motor (Located in Skokie, IL) 

   
 
         

LOT #307 QTY = 1

Stainless Serpentine Transfer Conveyor, 14" wide conveyor belt, 124" overall length, 31" infeed with 43" discharge height, Penta-Drive DC speed controller, 1/4 h.p. motor, 110 volts, 1 phase, 60 hz (Located in Skokie, IL)

   
 
         

LOT #308 QTY = 1

Hubert 125 Gallon Kettle, Ser. #12758, 39" X 32" vessel with 1.5" bottom outlet, 40 PSI, (3) stainless steel legs, 50" tall with cover (Located in Skokie, IL)

   
 
         

LOT #309 QTY = 1

Famco Mdl. JY Linker, 4" spaced crimpers, on rolling stand, 110 volts, 3 phase, 60 hz (Located in Skokie, IL)

   
 
         

LOT #310 QTY = 1

 

   
 
         

LOT #311 QTY = 1

 

   
 
         

LOT #312 QTY = 1

 

   
 
         

LOT #313 QTY = 1

 

   
 
         

LOT #314 QTY = 1

 

   
 
         

LOT #315 QTY = 1

Westfalia Mdl. SAMN5036 Separator/Desludger Disc Centrifuge, Ser. #1647143 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #316 QTY = 1

Rietz Desinigrator, 50 h.p., 460 volts, (3) 12" plates (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #317 QTY = 1

Westfalia Mdl. BRPX213 Separator/Desludger Disc Centrifuge, 60 h.p., 208/230 volts, 3 phase, 3 stage discharge, solids, water and oils, edible rendering (Located in Plano, IL)

   
 
         

LOT #318 QTY = 1

Lot (2) Hot Water/Steam Shrink Tunnels, 12" W X 12" T X 36" L tunnels (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #319 QTY = 1

Stainless Steel Smoke Truck, 37" W X 40" L X 80" T, 34-spaces, 2" apart (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #320 QTY = 1

Wright Flow Tech Mdl. 0600TRA01 Positive Displacement Pump, Ser. #30435002, 3 h.p., 230/460 volts, 3 phase motor (Located in Plano, IL)

   
 
         

LOT #321 QTY = 1

Waukesha Mdl. 030 Positive Displacement Pump, Ser. #30435002, 3 h.p., 230/460 volt, 3 phase motor (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #322 QTY = 1

Wilden Mdl. P200/PKPPP/WFS/WF/PWF Diaphragm Pump, Ser. #0030697026, Mfg. 11/2019 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #323 QTY = 1

Wilden Mdl. P200/PKPPP/TNU/TF/PTV Diaphragm Pump, Ser. #0030587272, Mfg. 10/2018 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #324 QTY = 1

Wilden Mdl. P200/SSPPP/BNS/BN/SBN/0730 Diaphragm Pump, Ser. #0021599884, Mfg. 04/2015 (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #325 QTY = 1

Pump (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #326 QTY = 1

APV Mdl. H9121 Stainless Steel Centrifugal Pump on 3 h.p., 230/460 volt motor, 1" outlet, 2" inlet (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #327 QTY = 1

APV Mdl. 1000002822768 Stainless Steel Centrifugal Pump on 3 h.p., 230/460 volt motor, 1" outlet, 2" inlet (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #328 QTY = 1

SPX Stainless Steel Centrifugal Pump, 2 h.p., 230/460 volt motor, 1" inlet, 2" outlet (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #329 QTY = 1

Young Engineering Portable Stainless Steel Pressure Tank, Ser. #469, operating pressure 120 psi (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #330 QTY = 1

Maja Mdl. ESM435 Manial Skinning Machine, new tooth roller, reconditioned (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #331 QTY = 1

Hobart Bandsaw, stainless steel table, mixed metal construction, plastic wheel covers, 220 volts, 3 phase (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #332 QTY = 1

Stainless Steel Incline Conveyor, 12" W X 11' L plastic belt, 24" tall stainless steel hopper, 69" discharge (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #333 QTY = 1

Multivac Mdl. AG800 Double Chamber Packaging Machine, Ser. #4814, 220 volts, Busch RA0160 vacuum pump, 7.5. h.p., 32" wide seal bars, 25" long, 4" deep lid (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #334 QTY = 1

Stainless Steel Conveyor, 9 1/2" W X 5' L plastic belt (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #335 QTY = 1

Stainless Steel Meat Truck, 31" W X 45" L X 22" D (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #336 QTY = 1

Stainless Steel Vat, 36" W X 53" L X 36" D on wheels (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #337 QTY = 1

Lot Weiler Mdl. 1109B (1) Block Guide, (1) 3 Point Mount, (2) Ring Holders, (2) Ring Wrenches (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #338 QTY = 2

Weiler Mdl. FP1000 Stainless Steel Auger Pullers (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #339 QTY = 4

Stainless Steel Drums, 22" Dia. X 32" Deep (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #340 QTY = 4

Stainless Steel Drums, 22" Dia. X 32" Deep (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #341 QTY = 2

Stainless Steel Drums, 22" Dia. X 34" Deep (Located in Plano, IL) Removal Starts Monday, November 22nd-By Appointment Only

   
 
         

LOT #342 QTY = 1

JDA Packaging Equipment Mdl. SC Stainless Steel Incline Screw Conveyor System, Ser. #10511, 27" W X 36" L X 21" D hopper, 4" dia. feed tube, 12' long, 220 volts, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #343 QTY = 1

Mueller Mdl. RBS Ribbon Blender, Ser. #F17206, 26.7 Cu. Ft. capacity, single shaft, non jacketed stainless steel bowl, 36" W X 36" L X 36" D, 8" bottom outlet, stainless steel cover with 8" dia. hole for loading product, 220 volts, 3 phase (Located in Sandwich, IL)

   
 
         

LOT #344 QTY = 1

Sweco Mdl. S18S55 Single Deck Separator Sifter, stainless steel fine mesh screen 14.5" dia., 4" dia. discharge, 1/4 h.p., 115 volts (Located in Sandwich, IL)

   
 
         

LOT #345 QTY = 1

Syntron Mdl. F-T0-2 Stainless Steel Vibratory Feed Hopper, Ser. #GPC157544, 24" W X 24" L X 21' D hopper on 6' tall frame (Located in Sandwich, IL)

   
 
         

LOT #346 QTY = 1

Apolo Mdl. CBS 910C Continuous Band Sealer, 26" long sealer on 5" wide conveyor belt (Located in Sandwich, IL)

   
 
         

LOT #347 QTY = 1

Uline Mdl. H-86 Foot Operated 24" Impulse Sealer, 34" stand height, 110 volts (Located in Sandwich, IL)

   
 
         

LOT #348 QTY = 1

Uline Foot Operated 14" Impulse Sealer, 33" stand height, 110 volts (Located in Sandwich, IL)

   
 
         

LOT # QTY =

 

   
 
         
 

Barliant
Auctions

Auction Calendar | Past Auctions | Mailing List | Appraisal Services | Contact Us

© 2013-2015, Barliant Auctions. All Rights Reserved
Barliant Auctions
518 Reimann Avenue
Sandwich, IL 60548
Phone: 815-570-2488
Fax:815-570-2541